Night Vision Thermal Overlay: Three Ways to Get One

Quick answer: a night vision thermal overlay draws the heat a thermal sensor sees on top of your night vision picture, so a warm person or animal stands out while the ground, trees and fences stay readable. There are three ways to get one: built in, in a fusion binocular such as our ELF-FB20 (from $7,799.95); clipped on, with a clip on thermal imager in front of one tube of a goggle you own, such as our Jerry-C Pro ($2,949.00); or side by side, a thermal and a night vision monocular on a bridge (from $749.95), which gives two pictures your brain merges rather than one overlay.

THROUGH THE GOGGLE

ELF-FB20 fusion modes, one scene.

One eyepiece view of deer in a field, cycling through every fusion mode. Tap a mode to jump to it.

Night vision onlyILLUSTRATION

Illustration. White hot and fire: seen in maker footage, not in the manual.

People look for an overlay because night vision alone has one weakness: something warm that stands still in shadow or brush blends into the scene. Thermal fixes that. Below: what an overlay looks like, the two overlay modes, the three ways to get one with a price for each, how each lines up, and what it does to your battery.

OUR PICK: HEAT & VIPER BRIDGE, $749.95. Not a single image overlay: heat in one eye, digital night vision in the other. It is the lowest cost way to have thermal and night vision together on your head, and the complete kit costs $149.95 less than the two monoculars alone. If you already own a PVS-14 or PVS-31, the Jerry-C Pro clip on gives you a true overlay in the same eye.

See the HEAT & VIPER BRIDGE kit

What is a night vision thermal overlay?

It is a heat picture laid over the night vision picture in the same view. The night vision tube still shows the scene by amplified light; the thermal sensor reads heat and draws warm targets on top. The ground, the fence line and the trees come from the tube. The person or animal pops out because of the heat.

Thermal overlay is one way of getting thermal fusion. For the bigger picture, with fusion goggles, clip ons and bridges side by side, see thermal fusion night vision.

Illustration of the view through the ELF-FB20 with thermal off: deer at the edge of a field
Thermal off: deer at the edge of a field are easy to miss through the tubes alone. Illustration from our product page, not a photo through a real unit.
Illustration of the same deer through the ELF-FB20 with the thermal overlay on in Highlight mode
The same deer with the thermal overlay on, in Highlight mode. Illustration from our product page, not a photo through a real unit.

Why add a thermal overlay to night vision?

Because each one fails where the other is strong. Night vision needs some light and shows detail, so you can read the ground and see where you put your feet. Thermal needs no light and finds heat through shadow and between thin branches, but on its own it shows little of the terrain. With an overlay you find the target with heat and read everything around it with the tube, without switching devices or taking your eye away. The strengths and limits of each are in night vision vs thermal.

What is the difference between Highlight and Outline?

Most overlays offer two main modes, and they suit different jobs.

  • Highlight fills warm targets with color or brightness over the night vision picture. It is the fastest way to spot a person or animal at a glance, but it covers the detail inside the target.
  • Outline draws only the warm edges. The night vision detail inside and around the target stays clear, so you can see what the animal is and what it is doing.

A common habit: find with Highlight, then watch with Outline. On the ELF-FB20 you can also switch the thermal off for night vision only. On the Jerry-C Pro, either mode can pulse on and off at a speed you set, so the overlay never hides tube detail for long. More on modes in COTI modes explained: Highlight and Outline.

Illustration of the view through a night vision tube with the Jerry-C Pro COTI in Highlight mode: warm bodies filled in bright
Highlight mode through a tube with the Jerry-C Pro clip on: warm bodies filled in bright. Illustration from our product page.
Illustration of the view through a night vision tube with the Jerry-C Pro COTI in Outline mode: a person and a dog on a forest track
Outline mode: only the warm edges of the person and the dog are drawn, so the tube detail stays visible. Illustration from our product page.

What are the three ways to get a thermal overlay, and what does each cost?

Three ways to get heat and night vision in one view (our product pages, read live 5 Nov 2026)
Way What you buy Price with us True overlay?
Built in (fusion binocular) ELF-FB20: two Gen 2+ tubes and a 640 x 512 thermal in one housing From $7,799.95 Yes, over both eyes
Clip on (COTI) Jerry-C Pro: a 640 x 512 thermal that clamps in front of one tube $2,949.00, plus a goggle if you need one (PVS-14 from $1,849.95) Yes, in one eye
Bridge HEAT thermal and VIPER digital night vision side by side $749.95 complete No: one picture per eye
Bridge with a tube PVS-14 + HEAT + BRIDGE kit From $2,349.95 No: one picture per eye

Built in: the fusion binocular

A fusion binocular has the thermal sensor in its own housing. Our ELF-FB20 puts a 640 x 512, 60 Hz thermal between two Gen 2+ tubes and blends it over both eyes through a 1280 x 1024 OLED, with under 30 ms of delay on its spec sheet. Its tubes are Gen 2+, not Gen 3. It is built to order and ships in about 5 to 7 weeks, to the USA and Canada.

The ELF-FB20 thermal fusion binocular from the side
Built in: the ELF-FB20 fusion binocular from the side.

Clip on: the COTI

The Jerry-C Pro COTI clip on thermal imager clipped onto a PVS-14 night vision monocular
Clip on: our Jerry-C Pro on a PVS-14.

A clip on thermal imager clamps in front of one tube of a goggle you already own and projects its heat picture into that tube. Our Jerry-C Pro does this on our PVS-14 and on one tube of our PVS-31 PRO, with a 35 x 30 degree overlay, no calibration, a wireless remote, a battery pack and the clamp ring set in the box. The full story is in clip on thermal for night vision.

Bridge: two devices, one per eye

A thermal monocular over one eye and a night vision monocular over the other. Your brain merges the two pictures, so it is not a true overlay, but it is the lowest cost way to have both. The HEAT & VIPER BRIDGE kit is $749.95 complete. HEAT and VIPER ship in roughly 25 to 35 days right now. Setup is in the PVS-14 and thermal bridge setup guide.

The HEAT thermal and VIPER digital night vision monoculars bridged on a head strap
Bridge: the HEAT thermal and VIPER digital night vision monoculars on one head strap.

Does a thermal overlay need lining up?

It depends on the way you choose.

  • Built in: no. On the ELF-FB20 the thermal is fixed in the housing, so there is nothing to clip on or line up.
  • Clip on: the Jerry-C Pro needs no calibration. To fit it: pick the clamp ring for your housing, clamp it square on the objective, turn it on and check that a warm object about 30 m away sits on its tube image. Because the thermal sensor sits slightly off the tube's axis, the overlay works from about 10 m out and lines up best past about 30 m. Very close objects can show the heat a little off the shape.
  • Bridge: there is no overlay to line up. Set each monocular in front of its eye, set the spacing so both pictures are full circles, and focus each one. Your eyes do the merging.

Some other clip ons let you calibrate the overlay by hand, and older or smaller ones cover a much narrower part of the tube picture (about 20 degrees on some models). The width of the overlay is worth checking on any clip on before you buy.

How much battery does a thermal overlay use?

A lot more than a tube. A tube runs for dozens of hours on one AA cell; a thermal sensor and its display drain a battery in hours.

Battery with the overlay on, as each product page states it
Device Power Runtime
ELF-FB20 External pack, 2 x 18650 on a coiled cable About 8 h thermal on; about 80 h night vision only
Jerry-C Pro 1 x CR123A (not included), or the included external pack About 3 h on a CR123A; about 10 h on the pack (at 22 C)
HEAT and VIPER Internal rechargeable (USB-C) plus an optional 18650 Up to 5 hours per charge

The habit that saves the most battery: overlay off when you only need to walk, on when you need to find something. Carry a spare and keep it warm in cold weather.

The ELF-FB20 external battery pack with its coiled cable
The ELF-FB20 external battery pack with its coiled cable.

Which thermal overlay should you buy?

  • You own a PVS-14 or PVS-31 PRO: the Jerry-C Pro clip on ($2,949.00) gives a true overlay in the eye you already use.
  • You want both views on your head for the least money: the HEAT & VIPER BRIDGE ($749.95). Not a true overlay, but both pictures at once.
  • You want an analog tube and thermal from scratch: the PVS-14 + HEAT + BRIDGE kit (from $2,349.95), and a clip on later if you want the overlay in one eye.
  • You want two tubes and the overlay over both eyes in one unit: the ELF-FB20 (from $7,799.95), built to order.

Comparing clip ons from different makers? See clip on thermal imagers compared and COTI vs fusion goggles.

What mistakes do people make with thermal overlays?

  • Leaving Highlight on all night. It hides detail inside the target; switch to Outline to watch.
  • Judging a clip on up close. The overlay is meant for 10 m and beyond; at arm's length it will look off.
  • Forgetting the battery math. The thermal half runs out long before the tube.
  • Calling a bridge an overlay. It is two pictures, one per eye. Great value, different experience.
  • Ignoring weight up front. A clip on adds about 90 g to the front of the goggle; balance the helmet.

Frequently asked questions

What is a night vision thermal overlay?

It is a heat picture from a thermal sensor drawn on top of the night vision picture, so warm people and animals stand out while the tube still shows the ground and the scene around them.

What is the difference between Highlight and Outline?

Highlight fills warm targets over the night vision image, which is the fastest way to spot them. Outline draws only their warm edges, so the night vision detail stays clear. Many owners find with Highlight and watch with Outline.

How do I add a thermal overlay to the night vision I own?

Use a clip on thermal imager. Our Jerry-C Pro at $2,949.00 clamps in front of our PVS-14 or one tube of our PVS-31 PRO and projects its heat picture into that tube, with no calibration.

Is a bridge setup a thermal overlay?

Not exactly. A bridge puts a thermal monocular over one eye and a night vision monocular over the other, and your brain merges the two pictures. Our HEAT and VIPER BRIDGE kit is $749.95 complete.

Does a clip on thermal overlay line up with the tube?

The Jerry-C Pro needs no calibration. Its overlay works from about 10 m out and lines up best past about 30 m; very close objects can show the heat slightly off the shape.

Does a thermal overlay drain the battery?

Yes, thermal uses much more power than a tube. Our ELF-FB20 runs about 8 hours with thermal on and about 80 hours with night vision only; the Jerry-C Pro runs about 3 hours on a CR123A or about 10 hours on its external pack.

Want thermal and night vision together without a five figure bill? The HEAT & VIPER BRIDGE kit is $749.95 complete: thermal in one eye, digital night vision in the other, and the bridge that joins them. 14 day returns; ships in roughly 25 to 35 days right now. Already own a tube? Add a true overlay with the Jerry-C Pro clip on.

Get the HEAT & VIPER BRIDGE, $749.95

Back to blog