FOM Meaning in Night Vision: What the Number Tells You

Illustration: a forest logging road on a dark night with no moon and a deer about 50 m out, seen side by side through a Gen 2+ tube (left) and a Gen 3 tube (right). The deer is easier to see on the Gen 3.ILLUSTRATION
Dark, no moon: the Gen 3 pulls clearly ahead; the deer at 50 m is easier to see. Illustration made by Night Operators from the measured 4MR Ranch blind test, not footage from it. Watch the full 4MR Ranch blind test video.

Quick answer: FOM means figure of merit. It is a night vision tube's resolution, in line pairs per millimeter (lp/mm), multiplied by its signal to noise ratio (SNR). A tube that resolves 64 lp/mm with an SNR of 22 has a FOM of 1,408. It is the best single number for comparing analog tubes: higher FOM means more detail and a cleaner picture as the light drops. It does not tell you everything (blemishes, halo and autogating sit outside it), and a "1400+" floor is not the same as a measured number for your tube.

TUBE GRADE

Slide the tube grade.

Same view, four tube grades. Drag the handle and watch the picture clean up as the figure of merit rises.

Four tube night view at the 1400-1550 FOM tube grade, illustrationFour tube night view at the 1600-1800 FOM tube grade, illustrationFour tube night view at the 1800-1950 FOM tube grade, illustrationFour tube night view at the 2000-2100 FOM tube grade, illustrationILLUSTRATION

TUBE GRADE 1400-1550 FOM

Illustration made from one real night view through one of our four tube goggles: each lower grade shows more haze, less contrast and less fine detail.

This guide covers what each half of the formula means, what a good FOM is for real use, why FOM tells you more than "Gen 2" or "Gen 3", how to read it on a QC sheet, and what each of our FOM tiers costs today.

PVS-14, 1400 to 1550 FOM, $1,849.95. A white phosphor Gen 2+ autogated tube in a published FOM range, with a printed QC sheet showing that tube's measured FOM, resolution and SNR. The PVS-14 comes with a G24 mount and J-arm.

See every FOM tier

What does FOM mean in night vision?

FOM stands for figure of merit. It is the standard one number grade for analog image intensifier tubes, used by tube makers, sellers and export rules to sort and price tubes. It has no unit; it is simply two measurements multiplied together.

It only applies to analog tubes. Digital night vision has a camera sensor and a screen instead of a tube, so it has no FOM. If a digital listing quotes one, ignore it. Thermal devices use different numbers again, such as sensor resolution and NETD.

How is FOM calculated?

FOM = resolution (lp/mm) x signal to noise ratio. Doing it by hand a few times makes any listing easy to read:

FOM worked out for four example tubes
Resolution SNR FOM What it means
54 lp/mm 18 972 Older or entry tube, grainy as light drops
64 lp/mm 22 1,408 Solid all rounder
68 lp/mm 25 1,700 Strong in darker nights
72 lp/mm 28 2,016 Top end of Gen 2+ production

Multiplying punishes weakness in either half. A tube with sharp resolution but noisy output still posts a middling FOM, and it deserves it: sharp noise is still noise. That is what makes FOM hard to game.

What do resolution and SNR each measure?

Resolution is detail. It counts how many alternating light and dark line pairs the tube can separate per millimeter on a test chart. More lp/mm means crisper edges and better identification at distance, the difference between seeing "an animal" and seeing which animal. Analog tubes usually run from the mid 50s to the low 70s.

USAF 1951 resolution test chart with converging bar patterns
Resolution is measured on a chart like this one: the finest bar pattern the tube can still separate sets its lp/mm figure.

SNR is cleanliness. It compares the real picture signal to the random noise the tube adds. Resolution is measured with plenty of light on the bench; SNR predicts what happens in deep dark, where a low SNR tube fills the scene with sparkling grain called scintillation. Two tubes with the same resolution can look very different under a thin moon, and SNR tells you which one keeps working.

In short: resolution sets the ceiling in good conditions, SNR decides how much of it survives bad ones. More depth on each is in what FOM and SNR tell you about Gen 2+ and Gen 3.

What is a good FOM for night vision?

For most civilian use, 1,400 to 1,550 is the value point, and 1,800 and up is worth it if you are often out under heavy cloud or tree cover with no moon.

Those bands match the tiers of our PVS-14 Gen 2+ night vision monocular, each shipped with a measured QC sheet.

FOM bands and what they suit
FOM band Picture Good for Our tier
Under 1,000 Grainy as light drops Bright moonlight, close range with an IR light Not offered
1,400 to 1,550 Strong all rounder with low light margin Property checks, wildlife watching, trail walking, darker rural nights $1,849.95
1,600 to 1,750 Cleaner in deep dark Frequent use in poor light, dense woods $2,299.95
1,800 to 2,000 Top of Gen 2+ production Overcast moonless nights, heavy canopy, long sessions $2,449.95

Prices are the PVS-14 STANDARD housing (40 degree view). The PRO housing (50 degree view) costs $1,884.95, $2,334.95 and $2,589.95 at the same three tiers. Our full tier by tier advice is in how to choose your FOM tier.

Is FOM more important than Gen 2 or Gen 3?

For comparing real units, yes. Generation describes how a tube is built (its photocathode and design era). FOM measures how one tube actually performs. Tubes vary a lot inside a generation, so a strong Gen 2+ tube can post a higher FOM than a tired or low grade Gen 3 tube. Two tubes with the same FOM look similar through the eyepiece whatever the label says.

Related: Gen 2 PVS-14 tiers by measured FOM, with the dealer label decoder.

Generation still matters in the darkest conditions, where Gen 3 photocathodes are more sensitive. If you truly work in near zero light every night, a high FOM Gen 3 unit is a different class of instrument. Most buyers are not in that group. The longer version is in Gen 2+ vs Gen 3 night vision.

Illustration: a lake shore with a wooden dock and a rowing boat under a full moon and a faint town glow, seen side by side through a Gen 2+ tube (left) and a Gen 3 tube (right). The two pictures look nearly the same; the Gen 3 is a little brighter.ILLUSTRATION
Illustration, close up, side by side: the dock planks and the far tree line with town lights magnified 3 times, Gen 2+ on the left and Gen 3 on the right. Nearly identical; the Gen 3 a little brighter.ILLUSTRATION
Full moon: nearly impossible to tell apart; the tester gave the Gen 2+ the edge on fine detail. Under it, the same spots magnified. Illustration made by Night Operators from the measured 4MR Ranch blind test, not footage from it. Watch the full 4MR Ranch blind test video.
Illustration: the inside of a very dark barn with tools on the wall and a sign at the far end, seen side by side through a Gen 2+ tube (left) and a Gen 3 tube (right). The Gen 3 picture is cleaner and the sign is readable.ILLUSTRATION
Illustration, close up, side by side: the far wall sign magnified 4 times and the tools on the wall 3 times, Gen 2+ on the left and Gen 3 on the right. The sign reads TACK ROOM on the Gen 3 and cannot be read on the Gen 2+.ILLUSTRATION
Very dark: the Gen 3 wins, with a cleaner picture and a readable sign. Under it, the same spots magnified. Illustration made by Night Operators from the measured 4MR Ranch blind test, not footage from it. Watch the full 4MR Ranch blind test video.

Under a moon the two are hard to tell apart; in real darkness the Gen 3 is clearly cleaner and sees more.

Why is a "1400+" FOM claim not a spec?

Because a floor only tells you the worst case. "FOM 1400+" covers anything from 1,400 to near 2,000, and those are very different tubes. When one price covers that whole spread, the tubes near the floor tend to go to floor price buyers. A real spec has a floor and a ceiling, like 1,400 to 1,550, and a measured sheet that names your tube's number.

To be fair to sellers, floor claims are often just what the paperwork upstream gives them. The fix is simple: buy from a published range, and ask for a per tube QC sheet with the serial number of your unit on it.

How do you read FOM on a QC sheet?

A QC sheet is the tube's test record: measured values from the bench, tied to a serial number. Every PVS-14 we ship comes with its own sheet showing that tube's measured FOM, SNR, resolution and blemish result. The lines to check:

  • Serial number. Match it to your unit first. A sheet that does not match proves nothing.
  • FOM. It should sit inside the tier you paid for.
  • Resolution and SNR. Multiply them. A result a few percent off the printed FOM is normal rounding (the bench uses raw values); a large gap is a fair question for your seller.
  • Dark spots. The blemish map shows whether any spot sits in the center of the view, where it matters, or at the edge.
  • Gain and sensitivity. How strongly the tube amplifies and how well the photocathode responds. Useful, but not part of FOM.
Hands holding a printed per-tube QC sheet listing measured values including FOM and a QC pass stamp
A printed per tube QC sheet: serial, measured resolution, gain, calculated FOM, the dark spot map and the pass stamp.

A real sheet, line by line

Here is a real sheet from one of our shipped units (tube type 1803WB), sold in an earlier, lower FOM tier we no longer offer, and what each line means:

One shipped tube's QC sheet
Sheet line This unit What it tells you
FOM 1301 Overall grade; inside the tier that unit was sold in
Resolution 65 lp/mm Detail ceiling in good light
SNR 20.33 How clean the picture stays as light drops
Luminance gain 8226 How strongly the tube amplifies incoming light
Luminous sensitivity 519 Photocathode response, in microamps per lumen
Uniformity 2.08 How even the brightness is across the picture
Useful cathode 17.5 mm Usable diameter of the input surface
Reliability 10,000 hours Rated tube life
Dark spots Zero, all zones Blemish map result; the center zones matter most

Multiply the two lines and you get 1,321, about 1.5 percent off the printed 1,301: the normal rounding gap described above, because the bench works from raw values. For a full line by line read of another real sheet, see inside a real PVS-14 QC sheet.

What does FOM not tell you?

  • Autogating. Protects the tube and your view around headlights and streetlights. It matters anywhere near people, whatever the FOM.
  • Blemishes. Two tubes with the same FOM can differ in where dark spots sit.
  • Halo. How much bright points bloom into rings.
  • Phosphor color. White or green is preference and does not enter the formula. See white phosphor night vision vs green.
  • Field of view and optics. A 50 degree housing shows more of the scene than a 40 degree one with the same tube.

Use FOM to pick your band and price, then use the full QC sheet to confirm the tube behind the number is clean and matched to your unit.

Related: how far you can see with night vision goggles at each tier.

What does each FOM tier cost, and how fast does it ship?

The PVS-14 night vision monocular, three quarter front view
The Night Operators PVS-14, sold in published FOM ranges with a measured sheet for each tube.

Our PVS-14 is sold in three FOM tiers today: 1,400 to 1,550 at $1,849.95, 1,600 to 1,750 at $2,299.95 and 1,800 to 2,000 at $2,449.95 (STANDARD housing; the 50 degree PRO housing starts at $1,884.95). Every tier uses a white phosphor Gen 2+ autogated tube with manual gain, and the product page lists a resolution range of 64 to 72 lp/mm and SNR of 22 to 28 across the line.

Shipping depends on the tier. The delivery line under the buy button tells you before you pay: a tier we hold at our US warehouse leaves in 1 to 2 business days, and a tier we build for you takes longer, with the 1,800 to 2,000 tier the slowest because high FOM tubes are the rarest. Tubes are graded after they are made, and only a small share test at 1,800 or above, which is also why that tier costs the most.

For both eyes, the PVS-31 PRO starts at $3,599.95 in the 1,400 to 1,550 tier.

Mistakes to avoid when buying by FOM

  • Buying on generation alone. Ask for the FOM, or better, the sheet.
  • Paying for headroom you will not use. Under a moon, 1,400 to 1,550 is plenty for most people.
  • Trusting a plus sign. "1400+" is a floor, not your number.
  • Comparing FOM on digital or thermal. Only analog tubes have one.
  • Ignoring the blemish map. A center spot bothers you every night, whatever the FOM.

Frequently asked questions

What does FOM mean in night vision?

FOM means figure of merit. It is a night vision tube's resolution in line pairs per millimeter multiplied by its signal to noise ratio, and it is the standard one number grade for comparing analog tubes.

How is FOM calculated?

FOM equals resolution in lp/mm times signal to noise ratio. A tube resolving 64 lp/mm with an SNR of 22 has a FOM of 1,408; one at 72 lp/mm and SNR 28 has a FOM of 2,016.

What is a good FOM for night vision?

For most civilian use under moonlight and starlight, 1,400 to 1,550 is the value point. Step up to 1,800 and above if you are often out under heavy cloud or tree cover with no moon.

Is a higher FOM always better?

Mostly. FOM captures detail and noise, which drive most of the picture, but it leaves out blemish placement, halo, autogating and field of view. Two tubes with the same FOM can still differ, which is why the full QC sheet matters.

Is FOM the same as Gen 2 or Gen 3?

No. Generation describes how a tube is built, while FOM measures how one tube performs. A strong Gen 2+ tube can have a higher FOM than a weak Gen 3 tube.

Does digital night vision have a FOM?

No. FOM only applies to analog image intensifier tubes. Digital night vision uses a camera sensor and a screen, so a FOM figure on a digital listing means nothing.

Can I see my tube's exact FOM?

Yes. Every Night Operators PVS-14 comes with its own QC sheet showing that tube's measured FOM, SNR and resolution, so you can check it against the serial number the day it arrives.

What is SNR in night vision?

SNR is signal to noise ratio, a measure of how much real picture signal the tube delivers compared with the random noise it adds. Higher SNR means a cleaner, less grainy picture in very low light. It is one of the two halves of FOM.

What does lp/mm mean?

Line pairs per millimeter, the standard measure of tube resolution. It counts how many alternating light and dark line pairs the tube can separate per millimeter on a test chart. Analog tubes usually measure from the mid 50s to the low 70s lp/mm.

Does autogating affect FOM?

No. Autogating is a power supply feature that protects the tube and steadies the picture around bright lights, and it is not part of the FOM formula. It still matters anywhere with headlights or streetlights, so check for it separately.

FOM turns night vision shopping from adjectives into arithmetic, and a measured sheet turns the claim into proof. The PVS-14 starts at $1,849.95 in the 1,400 to 1,550 FOM tier, with a white phosphor Gen 2+ autogated tube, the G24 mount and J-arm in the box, its own QC sheet, a 3 month hardware warranty and a 14 day return window. Sold direct, free US shipping.

Pick your FOM tier, from $1,849.95

Zurück zum Blog