
Quick answer: head mounted night vision goggles are night vision devices worn on your head so your hands stay free. You can carry them two ways: a head mount (a strap harness, often called a "skull crusher", with a small plate on the forehead) or a helmet mount (a helmet with a front shroud and a G24 pattern mount). A head mount costs less and is fine for short, standing sessions. A helmet is steadier, flips up out of the way, and balances with a rear weight, so it wins for anything past an hour or any walking. For most buyers the device to put on either one is a PVS-14 monocular: ours is $1,849.95 with the J-arm and a G24 pattern mount free in the box.
People search this three ways: "head mounted night vision goggles", "night vision monocular head mount" and "head mount vs helmet mount". Page one answers with digital listings that call a camera on a strap a goggle, and with patents for military headgear. What a buyer needs is simpler: which device is worth wearing on the head, which way to wear it, and what each way costs and feels like after an hour. That is this page.
PVS-14 kit, from $1,849.95. A Gen 2+ autogated analog monocular, 265 g or less without its battery, about 40 hours on one AA, true 1x so you can walk with it. The J-arm that fits a head mount or a helmet mount is in the box, and so is a free G24 helmet mount for the day you move to a helmet.
What are head mounted night vision goggles?
Any night vision device you wear instead of hold. The device sits a few centimetres in front of one eye (a monocular) or both (a binocular), held by an arm and a mount. Hands free is the whole point: you can open a gate, hold a leash, carry a light or a bag, and still see.
Three kinds of device get sold as "head mounted":
- Analog monoculars like the PVS-14. Light, passive (they work on starlight without an IR light), true 1x, and built with a standard dovetail for head and helmet mounts.
- Analog binoculars like the PVS-31 PRO. Two tubes for depth, heavier, built for helmets.
- Digital units: a camera and a small screen. The good ones are 1x and bridgeable; many low priced ones magnify the picture, which makes walking hard, and lean on an IR light. Our post on head mounting a digital monocular covers what works.
Head mount vs helmet mount: what is the difference?
A head mount is a fabric and strap harness with a small plate on the forehead. The plate accepts a J-arm, and the J-arm holds the monocular. No helmet needed, it packs flat, and it gets a PVS-14 in front of your eye in a minute.
A helmet mount swaps the harness for a helmet, usually a light bump helmet, with a shroud bolted to its front. A G24 pattern mount clicks into the shroud, and the same J-arm and monocular slide into the mount. The interface at the device is identical. What changes is everything that holds it to your head.
The J-arm is the shared link. Start on a harness, move to a helmet later, and the arm and the monocular come with you, settings and all.

How do they compare on comfort, stability and cost?
| Factor | Head mount (strap harness) | Helmet mount (helmet, shroud, G24, J-arm) |
|---|---|---|
| Up front cost | Lower: no helmet | Higher: a helmet, plus a counterweight. Our GEN II FAST SF bump helmet is $149.95 |
| Stability | Shifts when you move, needs re-seating | Locked; holds when you walk, duck or turn fast |
| Comfort after an hour | Front heavy; straps press on the forehead | Balanced with a rear weight or battery pack |
| Flip up out of the way | Limited | Yes, in a second |
| Weight it can carry | A light monocular | A monocular, a binocular, a quad, a thermal |
| Packing | Folds flat into a bag | Takes the space of a helmet |
| Best for | Short, mostly standing sessions | Regular, moving, hours long use |
The real trade is weight management. A harness hangs the monocular off the front of your skull with nothing behind to balance it, so after an hour the load pulls forward and the straps bite. A helmet spreads the contact over a wider shell and lets you hang weight at the back to cancel the forward pull. That rear weight is the single biggest comfort upgrade you can make.

Can you wear a night vision monocular on a head mount?
Yes. A monocular is the device a head mount was made for. A PVS-14 on a J-arm sits in front of one eye while the other eye keeps its own dark adaptation, so you can glance at a map or a phone without losing all your night vision. Keep it light: a monocular at around 265 g plus its arm is about the most a strap harness carries comfortably. Which eye to use is covered in which eye should wear the PVS-14.
Set it up the same way you would on a helmet: eye relief close, the tube centred on your eye, and the straps snug before dark. Then wear it around the house with the lens cap on for ten minutes; you will find every strap that needs adjusting before it matters.
Can you head mount night vision binoculars?
Not well on a harness. A two tube binocular is heavier in front and is built to hang from a helmet mount with a battery pack at the back as a counterweight. Our PVS-31 PRO ($3,599.95) is helmet only by design: it comes with an L4 G24 pattern mount and an AA x4 helmet battery pack that rides at the back. If you want two eyes, plan on a helmet from day one.
Which one fits how you use night vision?
Ask two questions: how long per session, and do you move. If you mostly scan from one spot and wear the monocular now and then, a head mount is enough and keeps your first spend down. If you walk ground, stay out for hours, or want the unit up and out of your face the instant you need bare eyes, the helmet earns its cost on the first long night.
| Use | Typical session | Pick |
|---|---|---|
| Checking the yard or a barn | Minutes, standing | Head mount or handheld |
| Wildlife watching from a blind | Hours, sitting | Head mount works; helmet is more comfortable |
| Walking property lines, trails, camping | Hours, moving | Helmet |
| Night airsoft and training | Hours, moving fast | Helmet |
| Binocular or quad | Any | Helmet |
One tube or two feeds the same decision. Our take on that is in PVS-14 vs PVS-31: monocular or binocular. Not every helmet works, either: a bike or ski helmet cannot take a night vision mount.
How do you move from a head mount to a helmet without wasting money?
Buy in the order you will feel. The monocular first, because ours already brings the J-arm and the G24 pattern mount. Then a bump helmet with a shroud. Then a counterweight sized to what hangs in front. Do not chase a fancy shroud before you own a counterweight: balance matters more than brand on a long night. The whole chain, part by part, is in our helmet mounted night vision setup guide.
Power weight counts too. On a helmet, a rear battery pack doubles as part of your counterweight; on a harness, every gram sits on your forehead. Runtimes for each device are in our night vision battery guide.

What about head mounted thermal and digital?
The same rules apply. Our HEAT & VIPER BRIDGE ($749.95) puts a thermal monocular in front of one eye and a true 1x digital night vision monocular in front of the other, on one bridge that is helmet ready (a G24 compatible mount is an add on). The HEAT weighs 360 g and the VIPER 320 g, so on a bare strap harness the pair is front heavy; most people who wear it for long run it on a helmet. It ships in roughly 25 to 35 days right now and does not record video.
For a thermal on its own, the helmet mounted thermal setup guide walks through the mount, the height and the balance.
For thermal units built to move between the hand and the helmet, see our best multi-role thermal monoculars guide.
What mistakes do people make with head mounted night vision?
- Too much weight on a harness. A binocular or a bridged pair on straps pulls forward within minutes.
- A magnifying digital unit. Anything above 1x makes steps and door frames look wrong. Wear only true 1x devices.
- Eye relief too far. A dark ring around the picture means the tube needs to come closer.
- No counterweight on a helmet. A helmet without rear weight is only slightly better than a harness.
- Buying the mount twice. Our PVS-14 and PVS-31 PRO already include the G24 pattern mount. Thermal and digital devices do not.
Who should buy what?
- Short sessions, smallest spend: a PVS-14 on a head mount harness. Move it to a helmet later with the same J-arm.
- Long nights or walking: the PVS-14 on a bump helmet with the free G24 pattern mount and a rear weight.
- Two eyes: the PVS-31 PRO, on a helmet.
- Heat and night vision together, lowest price: the HEAT & VIPER BRIDGE, best on a helmet.
- Who should not head mount at all: someone who glances out a window for a minute. Handheld is simpler.
Frequently asked questions
Is a skull crusher head mount bad for night vision?
No. It is a fair option for short and mostly standing use, and it keeps your first spend lower because you skip the helmet. Its limits are stability and comfort over time: the monocular hangs off the front of your head with nothing to balance it, so it shifts when you move and feels front heavy after about an hour.
Do I need a helmet to use a PVS-14?
No. A PVS-14 runs handheld, on a head mount harness, or on a helmet. A helmet with a shroud, a G24 pattern mount and the J-arm is the steadiest and most comfortable hands free option for long or moving sessions, but it is not required.
Can you head mount night vision binoculars?
Not well on a strap harness. A binocular is heavier in front and is built for a helmet mount with a rear battery pack as counterweight. Our PVS-31 PRO is helmet only and comes with an L4 G24 pattern mount and an AA x4 helmet battery pack.
What is the difference between a shroud and a G24 mount?
The shroud is the socket bolted to the front of the helmet. The G24 pattern mount clicks into the shroud and holds the J-arm or the binocular. Our PVS-14 and PVS-31 PRO come with the G24 pattern mount free; the shroud comes on the helmet.
Why does a helmet need a counterweight?
A device on the front of a helmet pulls it forward, tires your neck and slides the helmet down. A weight or battery pack at the back cancels that pull so the load sits balanced, which is the biggest comfort gain for long nights.
Can I move my PVS-14 from a head mount to a helmet later?
Yes. Both use the same J-arm. Unclip the arm from the harness plate, slide it into a G24 pattern mount on a helmet, and your eye relief and position carry over.
Head mount or helmet, the device is what you see through. Our PVS-14 kit is a Gen 2+ autogated analog monocular with the J-arm and a free G24 pattern helmet mount in the box, so it goes on a harness today and a helmet tomorrow. Free US shipping, a 14 day return window and a 3 month warranty.