Quick answer: To clean night vision goggles, blow the dust off the lenses first (a rubber blower or a lens pen brush), then wipe gently with a clean lens tissue or microfiber cloth and a drop of optical lens fluid, from the centre out. Never rub a dry cloth over grit, never use glass cleaner or dish soap, and never wipe the lens with your shirt. Wipe the body with a damp cloth. To store them, take the battery out, put both caps on, add a silica gel packet, and keep the case somewhere cool, dry and dark. Thermal and digital units follow the same rules with a few extras below.
This is our full care guide: the kit, a do and never table, the steps for analog tubes, digital units and thermal, long term storage, and the honest answer on purging.
OUR PICK: Night Operators PVS-14, from $1,849.95. IP67 on its page, argon nitrogen purged, Gen 2+ autogated tube with manual gain, caps in the box, and the G24-pattern helmet mount and J-arm free. See the PVS-14 tiers

What do you need to clean night vision goggles?
Five small things, all from a camera shop:
- A rubber blower (the squeeze bulb kind) to lift dust and sand off the glass without touching it.
- A lens pen or a soft lens brush for dust the blower leaves behind.
- Lens tissue or a clean microfiber lens cloth, kept in a bag so it stays clean. A dirty cloth is sandpaper.
- Optical lens fluid, the kind sold for camera lenses and eyeglasses with coatings.
- Cotton swabs and a little isopropyl alcohol, for battery contacts only, not for the lenses.
Add silica gel packets and a padded case for storage. That is the whole kit. Skip anything sold as a "cleaning spray" for screens or windows.
How do you clean night vision lenses?
- Switch off and take the battery out. You are about to touch the front of a live tube otherwise.
- Blow first. Hold the lens facing down and give it several puffs with the blower so grit falls away rather than settling back.
- Brush what is left. A few light strokes with the lens pen brush.
- Only now, go wet. Put one drop of lens fluid on the tissue or cloth, never straight on the lens, so it cannot creep into the gap around the glass.
- Wipe in a spiral. Start in the middle and work out to the edge with almost no pressure. Turn the cloth to a clean part and do one more pass dry.
- Do both ends. The eyepiece picks up skin oil and eyelash marks; it gets the same treatment.
- Check against a light. Look across the lens at an angle. Streaks mean too much fluid; wipe again with a dry, clean part of the cloth.
The coatings on night vision lenses are what let the most light through. They are tougher than they look but they scratch if grit is dragged across them, and every scratch scatters light. Cleaning is mostly about not dragging grit, which is why blowing comes first, every time. If you use the unit in dust or near water, a sacrificial window in front of the objective takes the wear instead of the lens: see sacrificial lenses and lens protection.
What should you never do when cleaning night vision?
| Do | Never | Why |
|---|---|---|
| Blow dust off with a rubber blower | Rub a dry cloth over visible grit | Grit dragged across the glass scratches the coating |
| Use lens tissue or a clean microfiber cloth | Use your shirt, paper towel or tissues | Fibres and dirt in them scratch, and paper leaves lint |
| Put one drop of lens fluid on the cloth | Spray or drip fluid straight on the lens | Fluid can creep around the edge of the glass |
| Clean battery contacts with a swab and a little isopropyl alcohol | Use glass cleaner, dish soap or detergents on the lenses | Ammonia and additives can attack lens coatings |
| Wipe the body with a damp cloth, then dry it | Rinse it under a tap or soak it | A water rating is for weather, not for washing |
| Take the battery out after use and before storage | Leave a battery in for weeks | A leaking cell corrodes the contacts and the compartment |
| Keep the caps on in daylight | Clean or test it with the tube on in daylight | Bright light ages an image tube |
| Let a cold unit warm up inside its closed case | Wipe off fog the moment you come indoors | Condensation dries off cleanly once the unit is warm |
How do you care for a PVS-14 or PVS-31 PRO?
These are analog units: a sealed image tube inside a housing. The PVS-14 and PVS-31 PRO pages both state IP67 and argon nitrogen purged, which means the housing is sealed against water and the space inside is filled with dry gas at the build. Your job is the outside.
- After every night: battery out, a puff of air on both lenses, caps on. If it got wet, pat it dry and let it air out before it goes in a closed case.
- Once a month in use: look at the battery cap O-ring and the contacts. Clean the contacts with a swab and a little isopropyl alcohol and let them dry. A drop of fresh battery corrosion means a cell leaked: replace it and clean the compartment at once.
- The eyecup: pull it off now and then and wipe out the sweat and dust. It is the dirtiest part of the unit.
- The mount and J-arm: wipe the dovetail and check the screws are snug, not tight.
- The binocular hinge (PVS-31 PRO): keep it clean and dry; do not oil it.
The tube itself is not something you can clean. It wears with use and with bright light, not with time on a shelf, which is why the daylight rule matters more than any cloth. How tubes age is in do night vision tubes wear out.

How do you care for digital night vision like the VIPER and HEAT?
Digital and digital thermal units have a camera sensor and a screen instead of a tube, and they live on lithium batteries. Lens cleaning is the same as above. The differences are power and water.
- Charging: the HEAT and VIPER have an internal battery that charges over USB-C, plus room for one 18650 cell in an outside compartment. Take the 18650 out before you charge over USB-C, as the product page says.
- Water: the page says water resistant, with no IP number. Rain is fine; dunking is not. Dry it off before it goes in a case.
- Screen and eyepiece: the eyepiece glass gets skin oil fastest. Clean it like a lens.
- Storage: lithium cells like to be stored part charged, not full and not flat, and somewhere cool. Charge it every couple of months if it sits.
Battery habits for digital units in the field, and how to store spare 18650 cells, are in digital night vision maintenance, cleaning and storage.
Can you clean a thermal lens the same way?
Almost the same, with more care. A thermal lens is not glass: it is germanium, the dull silver looking front lens, because ordinary glass blocks the heat a thermal camera sees. Germanium has a thin coating that does the real work, and it is softer than glass coatings.
- Blow first, always. More important on germanium than on glass.
- Lens tissue with a drop of lens fluid, very light pressure, spiral from the centre.
- No dry rubbing, no abrasive cloth, no strong solvents. A scratch through the coating shows as a mark in the thermal picture.
- Cap it when it is not in use. The front lens is the one part that sits out in front.
On the PREDATOR, the internal battery charges over USB-C and it can also take an optional 16340 cell that you supply. The product page says to remove the 16340 before USB-C charging, and it rates the unit water resistant, not for going under water. The page also offers PREDATOR CARE, a monthly plan that replaces a broken lens like for like once every 12 months.


How do you store night vision long term?
- Battery out. For anything longer than a week or two. A forgotten AA that leaks is one of the most common ways a healthy unit dies on a shelf.
- Clean and dry first. Do the lens routine above, and let the unit air dry if it was out in damp weather.
- Caps on, both ends. They keep dust and light off the glass.
- Silica gel in the case. A couple of packets. Swap them or dry them out every few months: once they are full they stop working.
- Cool, dry and dark. An inside closet is ideal. Garages, attics and cars swing through heat and damp, which is hard on seals, batteries and electronics.
- No window light. Never store it where the sun can reach the front lens, capped or not.
- Run it every few months. A short check at night (battery in, a few minutes on, battery out) tells you all is well and keeps the switches moving.
Moisture is the slow enemy. Damp storage can grow fungus on glass and corrode contacts, which is why the dry case matters more than the closet. How to carry the unit to and from the truck without dropping it or cooking it is in how to carry night vision: cases, bags and the truck. Cold nights add their own rules: see night vision in cold weather.
Related: dropped your night vision? the five checks before you panic.
Related: the tether that stops the drop at the truck.
Do night vision goggles need purging?
Not as routine care, and not by you. Purging means pushing dry nitrogen or argon through a housing to drive out moist air, so the inside of the lenses cannot fog or grow fungus. It is done at the build and, if a seal ever fails, as a service job.
Our PVS-14 and PVS-31 PRO pages state that the units are argon nitrogen purged and IP67. They are sealed: there is nothing to purge on a normal schedule, and you should not open purge screws or the housing yourself. If you ever see fog on the inside of a lens (fog that does not wipe off and does not clear when the unit warms up), or spots growing inside the glass, stop using it in the wet and contact us with a photo before you do anything else.
Fog on the outside of the eyepiece is a different problem with a different fix: your own warm breath and skin. That is covered in demisting and anti-fog for night vision eyepieces.
Mistakes that damage night vision
- The shirt wipe. The most common scratch on a night vision lens.
- Leaving the battery in. The most common shelf death.
- Storing it in the truck. Heat in summer and damp in winter, every day.
- Testing it in daylight with the cap off. Bright light wears the tube.
- Sealing it wet. A wet unit in a closed case is a damp box for weeks. Dry it first.
- Charging a digital or thermal unit with its spare cell inside. Both our product pages say take it out first.
Frequently asked questions
How do you clean night vision lenses?
Blow the dust off first with a rubber blower, brush off what is left, then put one drop of optical lens fluid on lens tissue or a clean microfiber cloth and wipe gently in a spiral from the centre out. Never rub a dry cloth over grit and never use glass cleaner.
How do you store night vision long term?
Take the battery out, clean and dry the unit, put both caps on, add silica gel packets to the case, and keep it somewhere cool, dry and dark, like an inside closet. Never store it in a garage, attic or car, and run it briefly every few months.
Should you take the batteries out?
Yes. Take the battery out after use and always for storage longer than a week or two. A forgotten cell can leak and corrode the contacts and compartment, which is one of the most common ways a healthy unit dies on a shelf.
Can you clean a thermal lens the same way?
Almost, with more care. A thermal lens is germanium with a soft coating, so always blow first, then use lens tissue with a drop of lens fluid and very light pressure. Never rub it dry, use an abrasive cloth or use strong solvents.
Do night vision goggles need purging?
Not as routine care. Purging fills the housing with dry gas so the inside cannot fog, and it is done at the build. Our PVS-14 and PVS-31 PRO pages state argon nitrogen purged and IP67. Do not open the housing yourself; if you see fog inside a lens, contact us with a photo.
Can I use glass cleaner on night vision?
No. Household glass cleaners and dish soap contain ammonia and additives that can attack lens coatings. Use a blower, lens tissue and optical lens fluid only.
Looked after this way, a good unit lasts for years of nights. Every Night Operators PVS-14 is IP67 and argon nitrogen purged on its page, ships with its lens caps, its own printed QC sheet, a free G24-pattern helmet mount and J-arm, a 3 month hardware warranty and a 14 day return window. Get the PVS-14 from $1,849.95