Helmet Mounted Thermal Monocular: Setup, Mount, Balance, Eye

Quick answer: to helmet mount a thermal monocular, you need a helmet with a front shroud, a flip up helmet mount such as a G24 style mount, and a thermal with a dovetail shoe that fits it. Slide the shoe in, set the height so the eyepiece sits square to your eye, put a counterweight on the back, and turn the screen brightness down. Keep the thermal light: most people are comfortable around 350 g or less out front, and the PREDATOR is about 339 g on its page (a pre-production figure). The Night Operators PREDATOR has the dovetail shoe built in.

Still deciding between a handheld and a helmet thermal? Our handheld vs helmet mounted thermal guide helps you choose; this page is the setup once you have chosen the helmet.

A thermal on your head is a different tool from a thermal in your hand. Your hands are free, the picture is always one glance away, and with the mount flipped up you are back to your naked eye in a second. Getting there takes four decisions: the mount, which eye, the height and the balance. This guide walks through each, using the PREDATOR as the example, and the same steps apply to most dovetail thermal monoculars.

Operator wearing the Night Operators PREDATOR thermal on a helmet mount, front view
Seen from the front: thermal over one eye, the other eye free. Picture made with Higgsfield from our real photo of the PREDATOR on the helmet.
A person wearing a helmet with the Night Operators PREDATOR thermal monocular over one eye in a gear room
Worn: the thermal sits over one eye on the helmet mount. Picture made with Higgsfield from our real photo.
A person in pine woods at night wearing a helmet with the Night Operators PREDATOR thermal monocular over one eye
At night in the woods: thermal in one eye, the other eye free. Picture made with Higgsfield from our real photo.

How do you mount a thermal monocular on a helmet?

You mount it in three layers: a helmet shroud, a helmet mount that clips into the shroud, and the thermal's dovetail shoe that slides into the mount.

  1. Helmet with a front shroud. Most helmets built for night vision have a shroud on the front. If yours does not, you need one before anything else. Our night vision helmet setup guide covers helmets and shrouds.
  2. Helmet mount. A G24 style mount clips into the shroud and holds the device in front of your eye. It also flips the device up and out of the way.
  3. Dovetail shoe. The thermal needs a dovetail shoe that matches the mount. The PREDATOR has one built into its housing, so it slides straight into the mount.

If you already run a PVS-14 on a helmet, you probably own most of this already. The PREDATOR's shoe fits PVS-14 pattern helmet mounts and J-arms.

Helmet ready: the PREDATOR slides into a G24 style mount on its built in dovetail shoe.

What mount and shoe do you need?

You need a PVS-14 pattern dovetail mount, such as a G24 style mount, and a thermal with a matching dovetail shoe. For the PREDATOR, that is our aluminum G24 style mount at $99.95, or a polymer version at $69.95.

Helmet setup parts for the PREDATOR (live prices 29 October 2026)
Part What it does Price
PREDATOR CORE The thermal, with dovetail shoe and rail adapter; the dual dovetail bridge is free for early bird orders while the launch window lasts $749.95
Aluminum G24 style helmet mount Holds the PREDATOR at your eye, flips up to stow $99.95
Polymer G24 style helmet mount Same job, lighter material $69.95
Helmet with a front shroud and a counterweight The base and the balance Your own

Read our G24 mount explainer for how the mount adjusts. A J-arm is only needed for a skull crusher head mount without a helmet, which we cover in head mount vs helmet mount.

Which thermal monoculars fit a PVS-14 pattern helmet mount?

Any thermal with a standard dovetail shoe, or an adapter that gives it one, fits a G24 style or other PVS-14 pattern helmet mount. Some units have the shoe built in; most need an adapter sold by their maker. Here are four that page 1 of a "helmet mounted thermal" search names, with the weight their maker or seller lists. We read each listing on 6 Nov 2026; weights are for the unit alone, before the mount, so add your mount and adapter on top.

Helmet thermals and how they fit a G24 style mount (listings read 6 Nov 2026)
Unit How it fits the mount Listed weight Source
Night Operators PREDATOR Dovetail shoe built in; drops into PVS-14 pattern mounts, J-arms and flip ups About 339 g without mounts (pre-production figure) Our product page
ATN Odin LT 320 Needs ATN's helmet mount kit; the seller suggests asking ATN about other arms About 285 g ATN spec as reported by AllOutdoor; OpticsPlanet listing for the mount
InfiRay (iRay USA) Mini MH25 V2 Needs the iRay USA dovetail adapter for the Mini series 12.1 oz (about 343 g) iRay USA product page
Trijicon IR Patrol M250 Wilcox style shoe listed as standard; a helmet kit version adds the mount 16 oz (about 454 g) EuroOptic listing

We give no rival prices here: they change often and depend on the kit. The point of the table is fit and weight. A unit with the shoe built in, like the PREDATOR, has one less part to buy and one less joint to work loose.

For five thermal monoculars built for both the hand and the helmet, side by side, see our best multi-role thermal monoculars guide.

Which eye for thermal when you add night vision later?

Put the thermal over the eye you will keep it on all night, and leave your other eye free or for night vision. Our own default is the PREDATOR over the right eye, with analog night vision over the left when you add it.

There is no single correct eye. What matters is that you choose one and stay with it, so your brain learns which eye carries the heat picture. If you plan to add a PVS-14 later on the dual dovetail bridge, think about which eye you want the night vision on, because that decides where the thermal goes. Our which eye for a PVS-14 guide covers eye dominance in detail.

Most people put the night vision on the dominant eye, because that is the eye that judges distance and footing, and the thermal on the other eye as the finder. Thermal mostly asks your brain "is something warm there?", which a weaker eye answers fine. If you start with thermal alone, set it on the eye it will keep once the PVS-14 arrives, so you never relearn the habit.

How do you set the height?

Set the height so the eyepiece sits square in front of your pupil, with the full screen visible and no dark edges. Then set the distance so the eyecup is close to your eye without touching your brow.

  1. Slide the PREDATOR into the mount and lock it.
  2. Lower the mount into the viewing position.
  3. Raise or lower the mount on its height adjustment until the round screen sits centered in your view.
  4. Move it left or right, if your mount allows, until the screen is not cut off on one side.
  5. Set the fore and aft distance so the whole screen is sharp and visible. Too far away and the edges fall off; too close and it rubs.
  6. Turn the rear diopter until the screen and the battery icon in the corner are sharp.

How do you balance the weight?

Balance it with weight on the back of the helmet. Our listing gives the PREDATOR at about 339 g without mounts, a pre-production figure, and that weight sits out in front of your face, so a counterweight on the back keeps the helmet from tipping forward.

Start with a counterweight, then adjust by feel: the helmet should sit level when you look straight ahead and should not pull your chin down after a few minutes. A tight chin strap and a properly fitted helmet matter as much as the weight itself. Our helmet counterweights guide covers what to use and where it goes. If you add a PVS-14 on the bridge later, you will need more counterweight, and the guide covers that too.

How heavy can a helmet thermal be before your neck complains?

There is no hard limit, but most people start to feel a front mounted device past about 350 g without a counterweight, and ATN's own guide to helmet thermals gives a similar line. What your neck feels is not the grams alone but the lever: the same weight sitting farther out in front of your face pulls harder.

  • Under about 350 g out front (a light thermal like the PREDATOR at about 339 g, plus a polymer mount): usually fine for an evening with a small counterweight.
  • About 350 to 500 g out front (heavier thermals, or a thermal plus an aluminum mount): plan on a counterweight from the first night.
  • Thermal plus night vision on a bridge (for example the PREDATOR beside a PVS-14 at 265 g or less): you are carrying two devices out front, so a counterweight or a rear battery pouch is a must.

The fix is always the same: move the device as close to your face as the eye relief allows, add weight on the back until the helmet sits level, and tighten the fit so the helmet does not rock. Our helmet counterweights guide covers what to use.

How do you set brightness so you keep your night eye?

Turn the screen brightness down to the lowest level where you can still read the picture comfortably. A bright screen ruins the night adaptation of the eye behind it and lights up your face.

On the PREDATOR, press the gear button once to open the brightness bar and use the minus and plus buttons to adjust it. Press the gear again for the contrast bar. Contrast is the control that makes a warm animal pop out of the background, so adjust it as conditions change. Press the gear a third time to close. There are ten buttons and no menus, so it is easy to do with gloves on, by feel. Our thermal palettes guide helps you pick a palette that is easy on the eye at night.

How do you flip it up and down?

The G24 style mount flips the PREDATOR up and out of your eye, and back down into position. Practice it at home in the light until it is automatic.

With the mount flipped up, you have your full naked eye view back. Many people walk with the thermal flipped up and drop it to scan, then flip it up again. Practice the motion with the helmet on so you do not have to look for the lever in the dark.

Can you add night vision on the other side later?

Yes. The PREDATOR's dual dovetail bridge is free for early bird orders while the launch window lasts, so you can add a PVS-14 pattern monocular over your other eye later. The bridge replaces the single mount position.

The bridge holds the PREDATOR on one side and the night vision monocular on the other, both on your helmet mount. Your PVS-14 needs a dovetail shoe to sit on the bridge; the angled J-arm many PVS-14s ship with will not work for this. Our thermal and night vision together guide and bridging guide cover the details.

What should you check before your first night out?

  • The mount is locked into the shroud and the shoe is locked into the mount.
  • The battery is charged. The internal battery charges over USB-C and runs 4 to 5 hours; an optional user supplied 16340 cell adds roughly 1.5 to 2 hours.
  • Brightness is low and the diopter is set.
  • The counterweight is on and the helmet sits level.
  • You can flip it up and down without looking.

Frequently asked questions

How do you mount a thermal monocular on a helmet?

You need a helmet with a front shroud, a helmet mount such as a G24 style mount that clips into the shroud, and a thermal with a dovetail shoe that slides into the mount. The PREDATOR has the dovetail shoe built in.

Which thermal monoculars fit a G24 helmet mount?

Any thermal with a standard dovetail shoe or an adapter that gives it one. The PREDATOR has the shoe built in. Units such as the ATN Odin LT, the InfiRay Mini and the Trijicon IR Patrol M250 fit with their maker's mount kit, adapter or shoe.

What helmet mount works with the PREDATOR?

PVS-14 pattern dovetail mounts, such as a G24 style mount. We sell an aluminum G24 style mount for $99.95 and a polymer version for $69.95.

How heavy can a helmet thermal be?

Most people are comfortable with about 350 g or less out front. The PREDATOR is about 339 g without mounts on our page, a pre-production figure. Past that, and always with night vision on a bridge, add a counterweight.

Which eye should a helmet thermal go on?

Pick one eye and stay with it. If you plan to add night vision, most people put the night vision on the dominant eye and the thermal on the other, so set the thermal on that eye from day one.

How do you keep your night vision with a thermal on your helmet?

Turn the screen brightness to the lowest comfortable level and flip the thermal up when you do not need it. On the PREDATOR, the gear button opens the brightness bar first, then contrast.

Can you add night vision next to a helmet thermal?

Yes. The PREDATOR's dual dovetail bridge, free for early bird orders while the launch window lasts, holds it beside a PVS-14 pattern monocular. The PVS-14 needs a dovetail shoe to sit on the bridge.

The PREDATOR has the dovetail shoe built in, so it drops into a G24 style helmet mount with no extra parts, and early bird orders get the dual dovetail bridge free for adding night vision later. Night Operators PREDATOR, $749.95; aluminum G24 style mount $99.95.

Shop the PREDATOR, $749.95

Add the aluminum G24 on the page if your helmet does not have one yet.

Retour au blog